Tag Archives: D6272

ASTM D6272 PDF

ASTM D – Air Permeability of Textile Fabrics . ASTM D – Standard Test Method for Flexural Properties Testing of Unreinforced and Reinforced. The Flexural test ASTM D measures the force required to bend a plastic beam under a four point loading system. The test method is used for reinforced or . ASTM D tests flexural properties of unreinforced and reinforced plastics and electrical insulating materials by four point bending. Learn more.

Author: Yobar Takasa
Country: Costa Rica
Language: English (Spanish)
Genre: History
Published (Last): 13 August 2005
Pages: 181
PDF File Size: 5.36 Mb
ePub File Size: 19.54 Mb
ISBN: 227-5-71304-113-5
Downloads: 27244
Price: Free* [*Free Regsitration Required]
Uploader: Gogul

In three point bending the maximum axial fiber stress is located immediately under the loading nose.

ASTM D6272

The arc of the loading noses in contact with the specimen shall be sufficiently large to prevent contact of the specimen with the sides of the noses see Fig. An example of a jig found to be useful is shown in Fig.

Please confirm that you agree with our privacy and cookies policy to submit this form.

Flexural strength should be determined x6272 a separate set of replicate specimens at a lower span-to-depth ratio that induces tensile failures in the outer? D beam along its lower face. Do not use the movement of the loading noses relative to the supports.

The AutoX is a high-resolution, long-travel automatic contacting extensometer. This intersection B is the corrected zerostrain point from which all extensions or strains must be measured, including the yield offset BEif applicable. The loading nose assembly shall be of the type which will not rotate. Measure the width and depth of the specimen to the nearest 0. The value obtained on specimens with machined surfaces may differ from those obtained on specimens with original surfaces.

Flexural Properties by Four-Point Bending ASTM D

Repeatability of calculations — When setting up the test, having an adequate preload is highly recommended to ensure accurate and consistent strain measurements. All dimensions must be stated in the report see also Note 6.

Flexural strain measurement — ASTM D requires that the method used to measure strain is not influenced by the compliance of the machine.

Procedure B is used for flexible, more ductile materials that undergo large deflections. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Instron ASTM D Flexural Properties of Plastics and Electrical Insulating Materials – Instron

Materials specifications aetm also be followed. Since the flexural properties of many materials can vary depending on temperature, rate of strain and specimen thickness, it may be appropriate to test materials at varied parameters.

Three recommended support span-to-depth ratios are Thicker specimens should be avoided if they exhibit signi? NOTE 14—When large support span-to-depth ratios are used, signi?

Hence, for these materials, an increase in span-to-depth ratio to It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Flexural stress at break Flexural modulus Mean, mPa where: The values provided in parentheses are for information only.

NOTE 3—Any necessary polishing of specimens shall be done only in the lengthwise direction of the specimen. However, for some highly anisotropic composites, shear deformation can signi? Both methods of calculation are described in the annex to Test Method D The specimen is supported on two lower anvils and the load is applied in the center of the specimen by a single upper anvil.

In three point bending the maximum axial? Precision and Bias The elastic modulus can be determined by dividing the stress at any point along the Line CD or its extension by the strain at the same point measured from Point B, de?

In such cases, the?

Specimen width shall not exceed one fourth of the support span for specimens greater than 3. Due to the very large number of tests offered, descriptions of those most commonly requested have been gathered into the following groups: See Annex A2 for information on the determination of and setting of the span.

ASTM D6272 Flexural Properties of Plastics and Electrical Insulating Materials

C6272 NOTE 11—In determination of the calculated value dd6272 some of the properties listed in this section it is necessary to determine if the toe compensation see Annex A1 adjustment must be made. For all tests, the support span shall be 16 tolerance 6 1 times the depth of the beam. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator.

For edgewise tests, the width of the specimen shall be the thickness of the sheet, and the depth shall not exceed the width see Notes 5 and 6.