12 Feb Regulation No 43 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of. E/ECE/ Rev.1/Add/Rev.2 E/ECE/TRANS/ Regulation No. 43 page 4 CONTENTS (continued) Annex 3 Annex 4 Annex 5 Annex 6 Annex 7 Annex 8. 29 Sep Mr. Masaru Morikawa, General Safety Subcommittee, JASIC. – Safety Glass Testing according to ECE R Mr. Pham Minh Thanh.
|Published (Last):||20 April 2009|
|PDF File Size:||1.96 Mb|
|ePub File Size:||15.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
This method permits eec of materials and components of a vehicle’s interior equipment individually or in combination up to a thickness of 13mm. These test methods ece r43 be used for approval, quality-control or product-evaluation purposes, as appropriate.
The nominal thickness of the interlayer or interlayers. The optical-distortion maximum for all directions M-M’ from the Ece r43 M.
Measurement of burning time starts at the moment when the ece r43 of the flame passes the first measuring point. In the case of laminated-glass panes other than windscreens, the tests shall be conducted on flat test pieces which are either cut from actual glass panes or ece r43 specially made.
Reason s for extension of approval: If the flame does not reach the last measuring point, measure the burnt distance up to the point where the ece r43 sce extinguished.
One test having given an unsatisfactory result, a new series of tests carried out on a new set of ece r43 pieces has given a satisfactory result.
The nature of the surface coating. The windscreen shall be mounted at the ece r43 angle of inclination as on the vehicle. The sample is not penetrated nor shall it break into fully separate large pieces. All the tests have ece r43 a satisfactory result; For the windscreens of N vehicles, the manufacturer may request that the same test may be carried out either in Test Area B defined in Annex 18, Paragraph 2.
The cross-cut test shall be carried ece r43 on one of the test pieces from 6. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. No impulse may be given to the phantom head by the drop appliance or by the measuring cable, so that it is accelerated only by gravity and falls vertically. Taber Test For the purpose of testing the resistance to abrasion, either the Taber test or as an equivalent alternative the package of Sand drop test, Car-wash test and Wiper ece r43 shall be ece r43.
The limits of the group are determined by developed area of ecw. Ece r43 of Windscreens Six complete windscreens from the smallest-developed-area series and six complete windscreens from the largest-developed-area series selected in accordance with the provisions of Annex 13, shall be tested. Ece r43 Test The purpose of this test is to determine whether the regular transmittance of safety glazing exceeds a specified value.
InterRegs: Regulation No. | ECE – United Nations
During irradiation the test pieces shall be exposed to water spray in continuous cycles. No impulse may ece r43 given to the phantom head by the drop appliance or by the measuring cable, so that it is accelerated only by gravity and ece r43 vertically. A few fragments of elongated shape shall ece r43 allowed, provided that: Quadrants are incorporated in the lower leg segments to measure knee angles.
The actual torso angle corresponds theoretically to the design torso angle for tolerances, see Paragraph 3. The safety glazing not covered by the definitions of Paragraphs 2.
Procedure The dimensions of the test specimen shall normally be those specified in the appropriate test method for the property or properties to be measured after exposure. Any additional markings, as described in Paragraph 5. A set of samples shall be considered satisfactory with regard to the test for resistance to chemical agents if one of the following conditions is met: The fragmentation tests must be repeated ece r43 transition from ece r43 plate glass to float glass or ece r43 glass, and vice versa.
Apparatus This method entails the projection of an appropriate slide raster onto the display screen through the safety glazing being tested. The check shall be carried exe on at least three samples per colour of interlayer taken from the daily production.
All glazing materials, including glazing material for the manufacture of windscreens, shall be such that, in the event of shattering, the danger of bodily injury is reduced as far as possible. A set of test pieces or samples submitted for approval shall be considered satisfactory from the point of ece r43 of the ece r43 for resistance to humidity if all the tests have given a satisfactory result.
Scope Two test methods are recognized: The above approval mark affixed to a multiple-glazed unit shows that the component concerned has been approved in the Netherlands E4 pursuant to Regulation No. All the tests give a satisfactory result. A set of test pieces subjected to approval testing rr43 be considered satisfactory from the point of view of ece r43 strength ece r43 one of the following conditions is met: Number of Samples 3. Evaluation The glazing shall be clamped to the supporting structure by eece of appropriate devices.
Test of Resistance to Abrasion 4. The temperature within the exposure apparatus during the dry portion of the cycle shall be controlled by circulation of sufficient air to ece r43 a constant black standard temperature. Ece r43 materials having burning rates differing according to the direction of the material ece r43 being established by preliminary tests the five or more samples shall be taken and be placed in the test apparatus in such a way that the highest burning rate t43 be measured.